• Supply GoPro 3 Hero3 HD Sports Camera Recorder Black Ultimate Edition with Battery


  • Supply 2013 version Ethernet Shield W5100 for Arduino UNO R3 Mega 2560 1280 A057(924)


  • Supply UNO ATmega328P ATmega8U2 Board w/ USB + Ethernet Shield W5100 for ARDUINO's IDE(H998B)


  • Supply ATmega2560-16AU Board + Ethernet Shield W5100 for Arduino 2560 A067(H912A)


  • Supply UNO R3 Rev3 Development Board ATmega328P ATMEGA16U2 AVR w/USB for Arduino(999)


  • Supply ATmega2560-16U2 Mega2560 R3 Rev3 Development Board w/USB for ARDUINO's IDE (902)


  • Supply L293D Motor Drive Shield for Arduino Mega 2560 UNO R3 AVR ATMEL


  • Supply CRIUS MAVLink-OSD V1.0 On-Screen Display MinimOSD for AIOP APM Telemetry ATMEGA328P


  • Arduino Nano V3.0 ATmega328P with USB Cable for Electronic Interactive (916)
    • images/v/201303/13642666690.jpg
    • images/v/201303/13642666691.jpg
  • Displaying 1/2

Arduino Nano V3.0 ATmega328P with USB Cable for Electronic Interactive (916)

  • item#: 916
  • Retail price: US$17.66
  • Price: 17.66

  • Start from: 1 Unit(s)
  • Weight: 0.2 Kg(s)

Estimate Shipping Costs

  • US$17.66 + Shipping Cost
    Quantity: Unit(s)



    Arduino Nano V3.0 ATmega328P with USB Cable for Electronic Interactive


  • 100% brand new

  • The duino Nano is a small, complete, and breadboard-friendly  board based on the ATmega328 (duino Nano 3.0) . It has more or less the same  functionality of the duino Duemilanove, but in a different package. It lacks  only a DC power jack, and works with a Mini-B USB cable instead of a standard  one.

  • Specifications:
    Microcontroller :                                                  Atmel ATmega328
    Operating Voltage (logic level) :                       5 V
    Input Voltage (recommended) :                        7-12 V
    Input Voltage (limits) :                                        6-20 V
    Digital I/O Pins :                                                 14 (of which 6 provide PWM output)
    Analog Input Pins :                                             8
    DC Current per I/O Pin :                                    40 mA
    Flash Memory :                                                  32 KB (ATmega328) of which 2 KB used by bootloader
    SRAM :                                                               2 KB (ATmega328)
    EEPROM :                                                         1 KB (ATmega328)
    Clock Speed :                                                    16 MHz
    Dimensions :                                                      0.73" x 1.70"

    The duino Nano can be powered via the Mini-B USB connection, 6-20V unregulated  external power supply (pin 30), or 5V regulated external power supply (pin 27).  The power source is automatically selected to the highest voltage source.

    The FTDI FT232RL chip on the Nano is only powered if the board is being powered  over USB. As a result, when running on external (non-USB) power, the 3.3V output  (which is supplied by the FTDI chip) is not available and the RX and TX LEDs  will flicker if digital pins 0 or 1 are high.
    Input and Output

    Each of the 14 digital pins on the Nano can be used as an input or output, using  pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts.  Each pin can provide or receive a maximum of 40 mA and has an internal pull-up  resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have  specialized functions:

    Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial  data. These pins are connected to the corresponding pins of the FTDI USB-to-TTL  Serial chip.

    External Interrupts: 2 and 3. These pins can be configured to trigger an  interrupt on a low value, a rising or falling edge, or a change in value. See  the attachInterrupt() function for details.

    PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite()  function.

    SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI  communication, which, although provided by the underlying hardware, is not  currently included in the duino language.

    LED: 13. There is a built-in LED connected to digital pin 13. When the pin is  HIGH value, the LED is on, when the pin is LOW, it's off.

    The Nano has 8 analog inputs, each of which provide 10 bits of resolution (i.e.  1024 different values). By default they measure from ground to 5 volts, though  is it possible to change the upper end of their range using the analogReference()  function. Additionally, some pins have specialized functionality:

    I2C: 4 (SDA) and 5 (SCL). Support I2C (TWI) communication using the Wire library  (documentation on the Wiring website).

    There are a couple of other pins on the board:

    AREF. Reference voltage for the analog inputs. Used with analogReference().

    Reset. Bring this line LOW to reset the microcontroller. Typically used to add a  reset button to shields which block the one on the board.

    1x Arduino Nano V3.0  ATmega328P
    1x USB cable

  • Write a Review:

    Tell us what you think about this item, share your opinion with other people. Please make sure that your review focus on this item. All the reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.

    Have any question or inquire for this item? Please contact Customer Service. (Our customer representative will get back shortly.)

      Indicates required fields*
      Your Name: *
      Enter your Reviewer Nickname
      Your Email: *
      Review Title: *

    Search Feedback

    • Did you find what you were looking for?
    • If you need help or have other feedback for Customer Service. Click here


    for the latest offers, discount and site activity!

    Online buy cheapest products direct from Chinese supply at rcmodelpart.com

    Join our community :
    rcmodelpart on Twitter rcmodelpart on Facebook rcmodelpart on YouTube


    Product Tags: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0-9 WishList

    Copyright © 2011 rcmodelpart.com. All Rights Reserved.